What size is a Polaris clutch puller?
Total length: 120mm. Threaded length: 50mm. Diameter of shaft: 16mm.
How do you remove a Polaris clutch without a puller?
- Flip the snowmobile on its side.
- Remove engine housing to expose the clutch.
- Remove clutch bolt.
- Wrap the Grade 8 bolt or clutch bolt with Teflon tape.
- Fill clutch bolt hole with water.
- Insert the bolt and tighten.
- Make repairs/replacements and then reassemble.
How do you remove a clutch without a puller?
- Flip the snowmobile on its side.
- Remove engine housing to expose the clutch.
- Remove clutch bolt.
- Wrap the Grade 8 bolt or clutch bolt with Teflon tape.
- Fill clutch bolt hole with water.
- Insert the bolt and tighten.
- Make repairs/replacements and then reassemble.
How do you make a Polaris clutch puller?
- Flip the snowmobile on its side.
- Remove engine housing to expose the clutch.
- Remove clutch bolt.
- Wrap the Grade 8 bolt or clutch bolt with Teflon tape.
- Fill clutch bolt hole with water.
- Insert the bolt and tighten.
- Make repairs/replacements and then reassemble.
What thread is a Polaris clutch puller?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you remove a Polaris secondary clutch?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you disassemble a Polaris secondary clutch?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you remove the primary clutch on a Polaris snowmobile?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you remove a primary clutch?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you remove a clutch?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you clean a snowmobile clutch without removing it?
- Step 1: Take the air compressor and blow out all of the dust, grit, and grime built up within the sheave area and the surrounding clutch components.
- Step 2: Spray the sheaves of both with brake cleaner.
- Step 3: Rub the sheaves (aka the clutch faces) with the abrasive pad.
How do you make a snowmobile clutch puller?
- Step 1: Take the air compressor and blow out all of the dust, grit, and grime built up within the sheave area and the surrounding clutch components.
- Step 2: Spray the sheaves of both with brake cleaner.
- Step 3: Rub the sheaves (aka the clutch faces) with the abrasive pad.
How do you make a Rzr clutch tool?
- Step 1: Take the air compressor and blow out all of the dust, grit, and grime built up within the sheave area and the surrounding clutch components.
- Step 2: Spray the sheaves of both with brake cleaner.
- Step 3: Rub the sheaves (aka the clutch faces) with the abrasive pad.
How do you use a clutch removal tool?
- Step 1: Take the air compressor and blow out all of the dust, grit, and grime built up within the sheave area and the surrounding clutch components.
- Step 2: Spray the sheaves of both with brake cleaner.
- Step 3: Rub the sheaves (aka the clutch faces) with the abrasive pad.
References:
- https://www.amazon.com/Secondary-Clutch-Polaris-1985-2009-Replaces/dp/B077NJS499
- https://snowmobilehow.com/how-to-remove-clutch-without-puller/
- https://www.youtube.com/watch?v=uXYE2-b0gxI
- https://www.youtube.com/watch?v=SiTjeaCzxDs
- https://www.otctools.com/products/primary-drive-clutch-puller
- https://www.youtube.com/watch?v=JBqvHMn95yA
- https://www.youtube.com/watch?v=COO-ka_iIKk
- https://www.youtube.com/watch?v=gIm0yALiGdY
- https://www.youtube.com/watch?v=mschqiplg0c
- https://www.youtube.com/watch?v=QcWELyTbdP4
- https://snowmobilehow.com/how-to-clean-snowmobile-clutch/
- https://www.youtube.com/watch?v=cc0wAMjNgow
- https://www.youtube.com/watch?v=O5iceu-7l4w
- https://www.youtube.com/watch?v=oWt_scFjg34